Hard Line Clips
Throughout my own builds, I have printed several items to accompany the newly installed parts to make it look nicer and hopefully leave it in a better designed state than its original OEM form all at a reasonable price.
This hard line clip can be used for any (4.75 mm) copper, nickel, or stainless lines throughout the engine bay or chassis. This clip is offered in multiple sizes to increase compatibility and allow for the clips to be applied to any line sizing.
Width dimensions are determined from measuring on the outer most diameter of each line. This is done to make obtaining an accurate measurement easier if the brake lines are still attached to the car or line size varies.
Sold as pack of 5 clips per purchase
Line Size
4.75 mm
Other sizes available upon request
Material Selection
Materials for these brackets are printed from filaments that have an HDT of at least 90 C, as most parts from a modern engine bay are made from ABS, allows for these products to withstand higher than average bay temperatures without deformation occurring.
For instance, any parts near a turbo or exhaust may experience some deformation due to certain material selections. Be aware some heat shield may be needed if installing parts in a non-standard location on the chassis, as this is the nature of car builds and engine swaps.
- ABS
- ASA
- ABS CF*
- ASA CF*
- Custom**
*additional fees may apply
**Custom choices in filament must have a minimum HDT of 90 C and may be subject to additional fees
Throughout my own builds, I have printed several items to accompany the newly installed parts to make it look nicer and hopefully leave it in a better designed state than its original OEM form all at a reasonable price.
This hard line clip can be used for any (4.75 mm) copper, nickel, or stainless lines throughout the engine bay or chassis. This clip is offered in multiple sizes to increase compatibility and allow for the clips to be applied to any line sizing.
Width dimensions are determined from measuring on the outer most diameter of each line. This is done to make obtaining an accurate measurement easier if the brake lines are still attached to the car or line size varies.
Sold as pack of 5 clips per purchase
Line Size
4.75 mm
Other sizes available upon request
Material Selection
Materials for these brackets are printed from filaments that have an HDT of at least 90 C, as most parts from a modern engine bay are made from ABS, allows for these products to withstand higher than average bay temperatures without deformation occurring.
For instance, any parts near a turbo or exhaust may experience some deformation due to certain material selections. Be aware some heat shield may be needed if installing parts in a non-standard location on the chassis, as this is the nature of car builds and engine swaps.
- ABS
- ASA
- ABS CF*
- ASA CF*
- Custom**
*additional fees may apply
**Custom choices in filament must have a minimum HDT of 90 C and may be subject to additional fees
Throughout my own builds, I have printed several items to accompany the newly installed parts to make it look nicer and hopefully leave it in a better designed state than its original OEM form all at a reasonable price.
This hard line clip can be used for any (4.75 mm) copper, nickel, or stainless lines throughout the engine bay or chassis. This clip is offered in multiple sizes to increase compatibility and allow for the clips to be applied to any line sizing.
Width dimensions are determined from measuring on the outer most diameter of each line. This is done to make obtaining an accurate measurement easier if the brake lines are still attached to the car or line size varies.
Sold as pack of 5 clips per purchase
Line Size
4.75 mm
Other sizes available upon request
Material Selection
Materials for these brackets are printed from filaments that have an HDT of at least 90 C, as most parts from a modern engine bay are made from ABS, allows for these products to withstand higher than average bay temperatures without deformation occurring.
For instance, any parts near a turbo or exhaust may experience some deformation due to certain material selections. Be aware some heat shield may be needed if installing parts in a non-standard location on the chassis, as this is the nature of car builds and engine swaps.
- ABS
- ASA
- ABS CF*
- ASA CF*
- Custom**
*additional fees may apply
**Custom choices in filament must have a minimum HDT of 90 C and may be subject to additional fees